Cutting Rafters Easily and Efficiently

One of the most time consuming tasks in homebuilding can be
the cutting of a roof. In some cases it can take as long to
cut and frame the roof as it does to frame the rest of the
house. It can also require a lot of space to get the job
done. It is in ones best interests to plan ahead during the
course of construction to be ready when it comes time to cut
the roof.

Whether the roof be a simple gable roof or a complex roof
with multiple hips and valleys you want to be able to cut
more than one rafter at a time. Sawhorses become a valuable
commodity during the roof cutting phase of construction.
Cutting a half dozen or more rafters is what you want to try
for. To achieve this there are a few options available to
the roof cutter.

If you only have one set of horses, nail an eight foot 2x4
flatwise to the top of them. This will allow you to mark and
cut six or more rafters depending on their width.

The second option is to use two pair of sawhorses. Just like
the previous option, nail a 2x4 flatwise over the top of two
horses. In this instance you are not limited to an eight
foot 2x4. You can use an 8, 10, 12, or even a 16' 2x4
depending on how much room you have to work in.

The third option is to make your own sawhorses out of a
2x10. Put legs on it just like a normal sawhorse. Again,
your only limitation is what you have available for length
of 2x10 and how much room you have to work.

Another time saver is to make a rafter pattern. To do this,
pick the straightest piece if lumber you can find from the
rafter material. Once you have determined the length of your
rafter from the plumb cut to the birdsmouth, the depth of
the birdsmouth, and the length of the rafter tail, transfer
this information to the material. After you have marked all
of this on the 2x, carefully and accurately cut the rafter.
This is going to be your pattern for the rest of the rafters
so you want to be precise with your cuts.

The next move is to nail stops to the top of the pattern.
Cut two pieces of plywood about 6" long by 2 1/2" wide. Nail
one to the top of the 2x about 2" from the plumb cut,
letting it hang over both edges of the 2x one half inch.
Nail the other piece just above the birdsmouth. You now have
a pattern to mark the rest of your rafters without having to
measure each and every one of them.

When you are ready to start cutting the rafters, lay as many
boards on the horse as you can and have enough room for the
saw to fit inbetween each one. When laying the boards on the
horses, have all the crowns pointing in the same direction
(When looking down a board while flat most boards are bowed
one way or the other. The convex side would be the crown).
Take the pattern and lay it on top of each board with the
plywood stops resting on the crowned edge and mark them.

You are now ready to cut rafters. When making your cuts, cut
the pencil line. Cut the plumb cut first and then move to
the birdsmouth and tail. Depending on how many rafters you
are cutting you may have to slide them back and forth so you
are not reaching over to far to make your cuts with the saw.
When cutting the birdsmouth it is okay to over cut it to
totally remove the material.

Homebuilding and cutting rafters can be a dangerous job.
Always exercise caution and safety when framing or using a
skilsaw.

Mike Merisko (C) 2006

www.sawkerfs.com

Article Source: http://www.diyarticlelibrary.com

Mike Merisko has been a carpenter for 26 years. Most of those years were spent in the homebuilding and remodeling industries. He was also in business as a carpentry and general contractor. While that is his forte, he also has experience in bridge building, commercial construction, and exhibit building which is how he earns his living these days. You can browse through articles by him and others at his website www.sawkerfs.com or visit his blog at www.sawkerfs.blogspot.com

Please Rate this Article

5 out of 54 out of 53 out of 52 out of 51 out of 5 

Not yet Rated