7 Simple Steps to Building Your Own Shed

Naturally, having a storage shed can come in handy when you have to store your garden equipment or need to protect your garden furniturein winter. If you are making a garden shed for the first time, start by researching the building of a shed. You can see will see that sheds are really straightforward structures that are no bother to construct. Below are seven simple stages you will find of use.

Phase 1:- Making the Foundation

At first before beginning building of the base (foundation), you will need to elect a location. Choose a position where there will be very good drainage. If too much water soaks near your shed base, you may slope the earth to guide the water away from your foundation. There are two most used foundations are the concrete foundation and the skid foundation. A concrete foundation will be everlasting & permanent, however the skid is not, choose the location discerningly. Start off by clearing and levelling off the spot. For a concrete foundation you have to construct the forms. Put down a layer of wire mesh to give support (reinforcement) and avoid cracking and pour the concrete. If you feel uncomfortable building a concrete slab foundation, perhaps consider using a skid base instead. Making a shed on a pressure treated skid base is easier for most DIYers.

A skid foundation will comprise of the skids, usually 4x4 pressure treated lumber, pressure treated floor bands, pressure treated floor joist and last but not least the plywood decking. You will put together the parts, before you lay down the plywood decking you'll need to square it off. First measure diagonally, shift the frame until each side measure equally, and install the flooring. To preserve the base from decay and rot, develop a gravel base. Lay a gravel base by taking away roughly four inches of ground, aboutand about twelve inches wider than the shed and fill it with gravel.

Phase 2:- Putting in the Walls

For the walls framing lumber will be used. The wall frame will consist of the wall band on the top and bottom and the wall studs in between each of the wall bands. Following on you stand up the walls and fasten (nail) them to your foundation. If the shed walls are not that large, you can install the siding while it is still on the floor and raise it afterwards.

Phase 3:- The Roof Frame

Constructing the roof frame is undeniablythe most challenging phase in building a shed. Take your time when preparing (cutting) the angles of the rafters. After you have your first truss frame put together, use it as a template to make the rest. Be careful here because if the roof truss are not accurately the same, the roof won't be even. use a miter saw to cut all the framing lumber, it makes cutting angles fast and easy.

Phase 4:- Siding and Roof Decking

Choice can be difficult when it comes to selecting the siding. The most commonly used is the T-11 exterior siding or Hardiboard. It is economical and simple to put up. Next put the siding of your choice to the walls. Next you can nail the plywood decking to the roof frame.

Phase 5:- Install Doors and Windows

There are plenty choices for a shed door. Maybe you want to build one or buy a door which is ready made or maybe even install a garage door. Dependant upon on your needs and how you plan to use your new space you can determine what what works for you. Double doors are very often used for storage sheds. Building your own double doors will make your shed practical and save you a little cash. For the best results search for free plans or buy plans when building a shed, plans will include all the details for the door and step by step instructions. Of course installing windows on a shed is optional. But if you decide to install windows, keep in mind how the sunlight will affect the shed. Windows will let in light making it easier to see, but it might also bring in too much heat.

Phase 6:- Installing Shingles

I don't need to warn you that working on the roof can be dangerous, think safety and take precautions at all times. Cover the roof plywood decking with roofing felt before placing on the shingles. The roofing felt will safeguard the plywood decking from leaks that could happen. As with most things there are lots of styles, types and sizes of shingles too choose from. When you install be sure to follow the manufacturer's product instructions for proper installation.

Phase 7:- Finising Touches - Trimming and Painting

Now the fun part giving your shed the finish touch, adding details like paint and trim will make your shed look beautiful and give it your ownpersonal touch. Paint will not only add appeal a good look, it will also guard it and make the shed longer lasting. Be mindful of any permits or regulations before you begin this project to ensure you don't go against any laws. Having detailed building plans will make constructing your shed simpler and you will also get better results.

Article Source: http://www.diyarticlelibrary.com

You can learn how to build Your own shed
Original Article Source

Please Rate this Article

5 out of 54 out of 53 out of 52 out of 51 out of 5 

Not yet Rated